GETTING STARTED WITH PLUMBING BASICS WHEN INSTALLING A BATHTUB

Getting Started with Plumbing Basics When Installing a Bathtub

Getting Started with Plumbing Basics When Installing a Bathtub

Blog Article

Click For More Info

What are your insights and beliefs on How to Install a Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is readily obtainable, the project can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub and set in the new one. Make sure you have actually qualified on your own for the task and are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Opportunities are you might require an expert plumber to make tube links.
This short article will assist you mount a new bath tub in your restroom if you have actually already purchased a new bathtub as well as don't need to transform the setup of your previous supply of water pipelines.
Your tools as well as material list need to make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old faucets with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic because of the restricted gain access to that is frequently the case.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
    Before proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next off, position the faucet in the placing opening in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous type must be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Tub


    Using the two wooden boards under its feet, place the bath tub in the required setting. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four small points.
    The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bathtub until the level checks out degree.
    To set up faucets, fit the bottom of the furthest flexible tap adapter to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
    Turn on the water supply and examine all joints as well as new pipework for leaks and tighten them if essential. Fill the bathtub and additionally examine the overflow electrical outlet and the normal outlet for leaks.
    Lastly, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bath tub must wait till the tub has actually been utilized a minimum of once as this will certainly resolve it right into its last placement.

    Preparing for the Setup


    To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid pressure on the tub.
    Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.

    Tiling Around the Bath tub


    In the area where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall between the bathroom and also the tiling, causing difficulties with moisture as well as feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealer can break relatively very early if you do not consider this movement before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is a good idea to fit the ceramic tiles using waterproof or waterproof sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We hope you enjoyed our topic about Tools You Need to Install a New Bathtub . Thank you for spending some time to read our short article. So long as you appreciated our post please don't forget to share it. Thanks a lot for taking the time to read it.


    Schedule Services

    Report this page